Step-by-Step Guide to Installing Rotors on a Rolls Royce

A Rolls Royce is more than just a luxury car—it's a mechanical masterpiece. When it's time to replace something as essential as brake rotors, the job requires care, precision, and quality components. Whether you're a seasoned DIYer or a passionate owner looking to understand your vehicle better, this guide breaks down the process of installing rotors on a Rolls Royce using trusted parts from Exotic Parts Depot.

What You’ll Need for the Job

Before diving in, assemble the necessary tools and safety gear:

• Floor jack and jack stands

• Lug wrench

• Socket wrench set

• Torque wrench

• C-clamp or brake caliper tool

• Wire brush

• Brake cleaner

• Rubber mallet

• Safety goggles and gloves

• Exotic Parts Depot rotors designed for Rolls Royce

Ensure the workspace is flat and well-lit, with enough room to move around the vehicle.

Step 1: Secure and Prepare the Vehicle

Begin by parking your Rolls Royce on a level surface. Apply the parking brake and use wheel chocks to keep the car from rolling. Loosen the lug nuts on the wheels where you’ll be replacing the rotors—but don’t remove them yet. Then, jack up the vehicle at the manufacturer-recommended lift points and place it securely on jack stands.

Step 2: Remove the Wheels

Now that the car is lifted and secure, remove the loosened lug nuts and take off the wheels. Place them aside in a safe spot where they won't get scratched or damaged.

Step 3: Detach the Brake Caliper

Locate the brake caliper—this is the component that presses the brake pads against the rotor. Using a socket wrench, remove the caliper bolts from the backside. Gently slide the caliper off the rotor and hang it using a bungee cord or zip tie. Never let the caliper dangle from the brake line as it can cause serious damage.

Step 4: Remove the Old Rotor

Check for retaining screws that might be holding the rotor in place. Remove these if present. If the rotor is rusted or stuck, a few firm taps with a rubber mallet around the hub area should loosen it. Once freed, slide the old rotor off carefully.

Step 5: Clean the Hub Surface

Use a wire brush and brake cleaner to scrub the hub clean. This step is critical—any rust, dirt, or buildup on the hub can lead to uneven rotor placement and brake vibrations.

Step 6: Install the New Rotor from Exotic Parts Depot

Before placing the new rotor onto the hub, spray it with brake cleaner to remove any protective residue from packaging. Line it up with the bolt holes or alignment pins and push it into place. If retaining screws were used, reinstall them securely.

Step 7: Reinstall the Brake Caliper

Check your brake pads—if they’re worn, replace them at the same time. Use the C-clamp or caliper tool to slowly push the caliper piston back into its housing, creating space for the rotor. Reposition the caliper over the new rotor and tighten the bolts to the manufacturer’s torque specifications.

Step 8: Reattach the Wheels

Put the wheels back onto the car and hand-tighten the lug nuts. Carefully lower the vehicle back to the ground using the jack. Then, use your torque wrench to tighten the lug nuts in a star pattern, following the correct torque values found in your owner’s manual.

Step 9: Bed the Brakes

To ensure the new rotors and brake pads function properly, perform a bedding-in procedure. This typically involves a series of moderate stops from 30-40 mph to evenly transfer brake pad material to the new rotors. Avoid aggressive braking during this period.

Maintenance Tips for Longevity

• Replace brake components in pairs (front or rear) to keep braking balanced.

• Inspect pads and rotors every 10,000 miles or as recommended by your vehicle’s manual.

• Use only high-quality parts like those from Exotic Parts Depot to maintain your Rolls Royce’s performance and value.

Why Rolls Royce Owners Trust Exotic Parts Depot

Not all rotors are created equal, especially when it comes to a vehicle like a Rolls Royce. Exotic Parts Depot offers performance-focused, model-specific rotors that uphold the high standards of luxury and reliability the brand represents. Each rotor is crafted with precision, ensuring seamless integration and superior braking performance. The best part? You get all of this at a cost far below what a dealership would charge—without sacrificing quality.

Whether you drive a Rolls Royce Ghost, Wraith, Dawn, or Phantom, Exotic Parts Depot has the exact-fit rotor options tailored to your model’s engineering. And because they specialize in exotic and luxury vehicles, you can count on knowledgeable support and parts that perform as expected.

Doing your own rotor installation on a Rolls Royce is a bold move—but with the right parts and guidance, it’s absolutely achievable. This hands-on approach gives you a deeper understanding of your vehicle and helps you maintain it with the same meticulous care that went into building it. By choosing rotors from Exotic Parts Depot, you’re not just saving money—you’re investing in performance and peace of mind. So take your time, follow each step, and enjoy the satisfaction of keeping your Rolls in impeccable condition.